CNTD CJY-E economy cylindrical inductive proximity sensors detect metal targets without mechanical contact. The range combines nickel-plated brass housings, red operating indicators and IP67 protection, with nominal detection distances from 1mm to 15mm. Choose the sensing head and installation clearance first, then match the output circuit and supply voltage to the control input.
All models below use 10–30VDC. DNA is NPN normally open, DNB is NPN normally closed, DPA is PNP normally open and DPB is PNP normally closed. DNC and DPC provide complementary NO+NC outputs and require four conductors. Combined outputs are listed for the M12, M18 and M30 groups only.
| Size / distance group | NPN models | PNP models |
|---|---|---|
| 04E / 1mm | CJY04E-01DNA CJY04E-01DNB | CJY04E-01DPA CJY04E-01DPB |
| 05E / 1mm | CJY05E-01DNA CJY05E-01DNB | CJY05E-01DPA CJY05E-01DPB |
| 06E / 1mm | CJY06E-01DNA CJY06E-01DNB | CJY06E-01DPA CJY06E-01DPB |
| 6.5E / 1.5mm | CJY6.5E-1.5DNA CJY6.5E-1.5DNB | CJY6.5E-1.5DPA CJY6.5E-1.5DPB |
| 08E / 1mm, flush | CJY08E-01DNA CJY08E-01DNB | CJY08E-01DPA CJY08E-01DPB |
| 08E / 2mm, nonflush | CJY08E-02DNA CJY08E-02DNB | CJY08E-02DPA CJY08E-02DPB |
| 12E / 2mm, flush | CJY12E-02DNA CJY12E-02DNB CJY12E-02DNC | CJY12E-02DPA CJY12E-02DPB CJY12E-02DPC |
| 12E / 4mm, nonflush | CJY12E-04DNA CJY12E-04DNB CJY12E-04DNC | CJY12E-04DPA CJY12E-04DPB CJY12E-04DPC |
| 18E / 5mm, flush | CJY18E-05DNA CJY18E-05DNB CJY18E-05DNC | CJY18E-05DPA CJY18E-05DPB CJY18E-05DPC |
| 18E / 8mm, nonflush | CJY18E-08DNA CJY18E-08DNB CJY18E-08DNC | CJY18E-08DPA CJY18E-08DPB CJY18E-08DPC |
| 30E / 10mm, flush | CJY30E-10DNA CJY30E-10DNB CJY30E-10DNC | CJY30E-10DPA CJY30E-10DPB CJY30E-10DPC |
| 30E / 15mm, nonflush | CJY30E-15DNA CJY30E-15DNB CJY30E-15DNC | CJY30E-15DPA CJY30E-15DPB CJY30E-15DPC |
| Head / sensing distance | DC normally open / normally closed | AC normally open / normally closed |
|---|---|---|
| M8 / 1mm | CJY08E-01DLA CJY08E-01DLB | No model listed |
| M8 / 2mm | CJY08E-02DLA CJY08E-02DLB | No model listed |
| M12 / 2mm | CJY12E-02DLA CJY12E-02DLB | No model listed |
| M12 / 4mm | CJY12E-04DLA CJY12E-04DLB | CJY12E-04AKA CJY12E-04AKB |
| M18 / 5mm | CJY18E-05DLA CJY18E-05DLB | CJY18E-05AKA CJY18E-05AKB |
| M18 / 8mm | CJY18E-08DLA CJY18E-08DLB | CJY18E-08AKA CJY18E-08AKB |
| M30 / 10mm | CJY30E-10DLA CJY30E-10DLB | CJY30E-10AKA CJY30E-10AKB |
| M30 / 15mm | CJY30E-15DLA CJY30E-15DLB | CJY30E-15AKA CJY30E-15AKB |
| Size / distance code | Nominal sensing distance | Setting distance | Standard iron target | DC response frequency |
|---|---|---|---|---|
| 04E-01 | 1mm | 0–0.8mm | 6×6×1mm | 1500Hz |
| 05E-01 | 7×7×1mm | |||
| 06E-01 | 8×8×1mm | 1000Hz | ||
| 6.5E-1.5 | 1.5mm | 0–1.05mm | 8×8×1.5mm | |
| 08E-01 | 1mm | 0–0.8mm | 8×8×1mm | |
| 08E-02 | 2mm | 0–1.4mm | ||
| 12E-02 | 2mm | 0–1.4mm | 12×12×1mm | 1000Hz |
| 12E-04 | 4mm | 0–2.8mm | 500Hz | |
| 18E-05 | 5mm | 0–3.5mm | 18×18×1mm | 350Hz |
| 18E-08 | 8mm | 0–5.6mm | 25×25×1mm | |
| 30E-10 | 10mm | 0–7mm | 30×30×1mm | 350Hz standard; 400Hz premium DC transistor version |
| 30E-15 | 15mm | 0–10.5mm | 45×45×1mm | 200Hz |
Use 350Hz for the M18 5mm group. All listed AC two-wire models are 20Hz. Frequencies are average values measured with the standard target, spacing between successive targets equal to twice the target width, and a target-to-sensor gap of half the nominal sensing distance. Set the actual operating gap within the setting range.
| Parameter | DC NPN / PNP | DC two-wire | AC two-wire |
|---|---|---|---|
| Operating voltage | 10–30VDC | 90–250VAC | |
| Control output | 200mA maximum | ||
| Leakage current | ≤10mA | ≤0.6mA | ≤10mA |
| Residual voltage | ≤1V | ≤3.5V | ≤10V |
| Protection circuit | Surge, reverse-polarity and overcurrent protection | Surge protection | |
| Hysteresis | ≤10% of nominal sensing distance | ||
| Temperature influence | Within ±10% of the sensing distance at 20°C over −25 to +70°C | ||
| Size group | Cable outside diameter | Standard length | Conductors | Strands per conductor |
|---|---|---|---|---|
| 04E, 05E, 06E, 6.5E | 2.8mm | 2m | 3P | 22 |
| 08E | 1.5m | 3P for NPN/PNP; 2P for DC two-wire | ||
| 12E | 3.8mm | 3P for a single NPN/PNP output; 4P for NO+NC; 2P for DC or AC two-wire | 25 | |
| 18E, 30E | 4.8mm | 30 |
The cable specification identifies AWG22, 0.1mm individual strand diameter and 1.25mm conductor insulation outside diameter. The strand counts above are strands within each conductor, not the number of external connections. Standard cable is gray PVC; the black cable option is oil-resistant PVC.
| Position | Code element | Meaning and choices |
|---|---|---|
| 1 | CJ | Inductive sensing |
| 2 | Y | Cylindrical metal housing |
| 3 | Size | 08=M8, 12=M12, 18=M18, 30=M30. The miniature specification separately lists 04, 05, 06 and 6.5 size codes. |
| 4 | E | Economy series |
| 5 | Thread length | Blank=standard; L=long threaded version. Dimensions below apply to the illustrated standard models. |
| 6 | Sensing distance | 01=1mm, 02=2mm, 04=4mm, 05=5mm, 08=8mm, 10=10mm, 15=15mm; the 6.5E miniature models use the literal 1.5 distance code. |
| 7 | Supply | A=90–250VAC; D=10–30VDC. The wider ordering guide also describes E=20–60VDC and J=5–10VDC; these are not additional full models in the selection tables. |
| 8 | Output circuit | N=NPN; P=PNP; K=AC two-wire; L=DC two-wire |
| 9 | Output state | A=NO; B=NC; C=NO+NC. Use C only for the model groups that list it. |
| 10 | Connection | Blank=free-ended cable; M=straight male M12 four-pin A-coded connector. M-type, DT, AMP and SM connector families are also shown with configuration subcodes; their individual subcodes are not defined in the guide. |
| 11 | Cable material | Blank=PVC; U=PUR; VP=shielded PVC; UP=shielded PUR |
| 12 | Lead length | Blank is shown for a direct M-type connector body. L1–L5 denote lead-length choices, with L1=1m and the range not restricted to L5. Standard supplied cable lengths are those in the cable table. |
| Housing | Thread | Overall axial reference | Thread-length reference | Front projection | Nut / across-flats reference |
|---|---|---|---|---|---|
| CJY08E-01, flush | M8×1 | 52mm | 38mm | Flush face | Ø15mm / 13mm; nut thickness 3mm |
| CJY08E-02, nonflush | 47mm | 32mm | 5mm | ||
| CJY12E-02, flush | M12×1 | 58mm | 38mm | Flush face | Ø21mm / 17mm; nut thickness 4mm |
| CJY12E-04, nonflush | 53mm | 32mm | 7mm | ||
| CJY18E-05, flush | M18×1 | 63mm | 38mm | Flush face | Ø29mm / 24mm; nut thickness 4mm |
| CJY18E-08, nonflush | 58mm | 32mm | 10mm | ||
| CJY30E-10, flush | M30×1.5 | 67mm | 38mm | Flush face | Ø41mm / 36mm; nut thickness 5mm |
| CJY30E-15, nonflush | 59mm | 32mm | 11mm |
These axial references follow the drawing endpoints and exclude the free cable. The attached drawings show the cable exit, indicator and mounting-nut geometry. The miniature 04E–6.5E groups have electrical specifications but no corresponding dimension drawings in this attachment.
Use the lettered geometry in the attached installation drawing: A is face-to-face spacing; B is parallel spacing; n is the required head exposure reference; Ød is the surrounding-metal opening diameter; ℓ and m are the axial / surrounding-metal references shown in the drawing. Values below are in millimeters and preserve the illustrated measurement endpoints.
| Model group | A | B | n | Ød | ℓ | m |
|---|---|---|---|---|---|---|
| CJY08E-01 | 9 | 16 | 0 | 8 | 4.5 | 12 |
| CJY08E-02 | 12 | 24 | 8 | 24 | 6 | 24 |
| CJY12E-02 | 12 | 24 | 0 | 12 | 6 | 18 |
| CJY12E-04 | 24 | 36 | 11 | 36 | 12 | 36 |
| CJY18E-05 | 30 | 36 | 0 | 18 | 15 | 27 |
| CJY18E-08 | 48 | 54 | 14 | 54 | 24 | 54 |
| CJY30E-10 | 60 | 60 | 0 | 30 | 30 | 45 |
| CJY30E-15 | 90 | 90 | 15 | 90 | 45 | 90 |
For a single NPN/PNP output, brown connects to +V, blue to 0V and black is the output. Connect the load between +V and black for NPN, or between black and 0V for PNP. DC and AC two-wire sensors connect in series with the load; the diagrams allow the load in either lead. Use 90–250VAC for the listed AC models. The attachment retains circuit and NO/NC timing diagrams; the single-output diagrams do not define the fourth conductor of a NO+NC model.
| Illustrated device | Sensor supply | Sensor output | Scope |
|---|---|---|---|
| PA10-U, input 1 | Brown to terminal 9 (+12V); blue to 10 (GND) | Black to 11 (IN1) | External NPN three-wire connection examples; not additional sensor model designations |
| PA10-U, input 2 | Brown to 13 (+12V); blue to 14 (GND) | Black to 15 (IN2) | |
| FX4 counter | Brown to 10 (+12V); blue to 11 (0V) | Black to 8 (CP1) | Counter illustration uses a 100–240VAC counter supply; this is not the sensor supply voltage |
| Item | Specification |
|---|---|
| Enclosure protection / indication | IP67; red operating LED |
| Operating / storage temperature | −25 to +70°C / −30 to +80°C, without icing |
| Humidity | 35–95%RH, without condensation |
| Insulation resistance | ≥50MΩ at 500VDC |
| Dielectric strength | 1500VAC at 50/60Hz for 1min |
| Vibration | 1mm amplitude, 10–55Hz swept over 1min, 2h in each X/Y/Z direction |
| Shock | 500m/s², approximately 50G, three times in each X/Y/Z direction |
| Materials | Nickel-plated brass case and nuts; nickel-plated iron washers; PBT sensing face; PVC cable |
| Referenced standards | CCC: GB/T14048.10; TÜV and CE: EN60947-5-2. Supporting certification documents are not included with the selection guide. |
| Utilization-category references | DC-13: 10–30VDC, 200mA; AC-140: 24–250VAC, 200mA. These category references do not replace the operating-voltage ratings of individual models. |
Use these sensors for ordinary industrial metal-position detection within the specified target, gap, load and environmental conditions. Regional versions can differ. The manufacturer excludes personnel-safety functions, exceptionally high-reliability systems such as nuclear, gas and power infrastructure, severe outdoor or contaminated environments, fire or explosion hazards, strong acids or alkalis, and military or aerospace use unless specifically designed and confirmed for that application.
