| Part Number: | ULO | - | TB40 | - | 65C | / | A | - | 02 | P | - | 3 | 100A |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Explanation: |
Brand |
Series Code |
Terminal Form 65C - Centred straight pins |
Housing A - End fixing |
Poles 02–24 - Two-digit count from 2 to 24 poles |
Pole Suffix |
Colour 1 - Grey |
Customer Requirements 100A - Standard suffix shown in the eight model drawings |
The 65 family provides single-row screw connections at 11mm pitch. A housings have end fixing holes; B housings omit the fixing ends. C versions use centred straight pins, S versions use offset straight pins, H versions have extended eyelet tabs, and R versions have bent solder terminals. All eight models support 2–24 poles.
| Model | Terminal arrangement | Housing | Pitch |
|---|---|---|---|
| TB40-65C/A | Centred straight pins | A, end fixing | 11mm |
| TB40-65C/B | B, no fixing ends | ||
| TB40-65S/A | Offset straight pins | A, end fixing | |
| TB40-65S/B | B, no fixing ends | ||
| TB40-65H/A | Extended eyelet tabs | A, end fixing | |
| TB40-65H/B | B, no fixing ends | ||
| TB40-65R/A | Bent solder terminals | A, end fixing | |
| TB40-65R/B | B, no fixing ends |
| Model | IEC overvoltage category | Pollution degree | Rated current | Rated voltage | Impulse voltage |
|---|---|---|---|---|---|
| 65C/A | III | 2 | 32A | 300V | 4kV |
| 65C/B | 8kV | ||||
| 65S/A and 65S/B | 4kV | ||||
| 65H/A | |||||
| 65H/B | 3 | 41A | 500V | 6kV | |
| 2 | 600V | ||||
| II | 1000V | ||||
| 65R/A and 65R/B | III | 32A | 300V | 4kV |
Other IEC condition combinations are not specified for the models rated 32A. The 65H/B rating does not apply to 65H/A or to other termination styles.
| UL use group | Rated current | Rated voltage | Wire range |
|---|---|---|---|
| B | 30A | 300V | 22–10AWG |
| C | Not specified | Not specified | Not specified by group |
| D | 10A | 300V | 22–10AWG |
The UL ratings apply to all eight models. Metric conductor cross sections are not specified.
| Parameter | Specification |
|---|---|
| Connection | M4 screw connection, 1.2N·m tightening torque |
| Strip length | 12mm for 65C/A, 65S/A, 65S/B, 65H/A, 65H/B, 65R/A and 65R/B; not specified for 65C/B |
| Housing | PA66, UL94V-0 |
| Insulation material group | I |
| Screw material | Nickel-plated steel |
| Solder terminal material | Tin-plated brass |
| Protection rating | IP20 |
| Operating temperature | -40°C to +105°C |
| RoHS compliance | Declared |
| Separate fixing screw size and torque | Not specified |
| Field | Selection |
|---|---|
| Model | TB40 with 65C/A, 65C/B, 65S/A, 65S/B, 65H/A, 65H/B, 65R/A or 65R/B |
| Pole code | 02P–24P |
| Colour code | 1: Grey; 2: Blue; 3: Black; 4: Green; 5: Orange; 6: Red; 7: Transparent; 8: Yellow; 9: White |
| Customer requirement suffix | 100A as shown in the model designations |
Dimensions are in millimetres. N denotes the number of electrical poles; drawings that use P follow the same pole-count convention. All bodies have a nominal 18.00 height and 17.30 depth. Contact-to-contact pitch is 11.00, and the first-to-last contact span is 11×(N−1).
| Housing | Overall length | Fixing-hole centre span | Fixing aperture |
|---|---|---|---|
| A | 11×(N+1)+13.00 | 11×(N+1) | 3.40 diameter |
| B | 11×(N−1)+13.00 | Not applicable | Not applicable |
A housings place each fixing centre one pitch beyond the nearest electrical contact. Match the termination style as well as the housing when designing a board or mounting fixture.
| Style | Terminal width × thickness | Terminal projection | PCB opening | Additional position details |
|---|---|---|---|---|
| 65C/A and 65C/B | 2.00±0.10 × 1.00±0.10 | 6.30±0.30 below body | 2.50×1.70 for C/A; 2.49×1.70 for C/B | Centred, 8.65 from body edge |
| 65S/A and 65S/B | 6.00±0.30 below body | 2.50×1.70 | Offset, 4.40 from indicated body edge | |
| 65H/A and 65H/B | 4.00 nominal × 1.00 nominal | 12.90±0.30 below body | 5.00×1.50 | H/B shows a 2.00×3.00 eyelet and 8.65 edge offset |
| 65R/A and 65R/B | 4.00±0.10 at tab base; 2.00±0.10 at tip; 1.00±0.10 thick | 5.75±0.30 outward; 5.20±0.30 below body | 2.50×1.70 | Bent terminal orientation shown in the respective outlines |
The H/A drawing specifies ±0.10 on tab width and thickness; H/B shows nominal 4.00 and 1.00 dimensions. Preserve each model's drawing tolerances. The 65C and 65S galleries can look similar from above, while their centred and offset tail positions require different footprints.
Apply these values only where an individual dimension does not specify a tolerance.
| Dimension range | Total pitch tolerance | Nominal dimension tolerance |
|---|---|---|
| Over 0mm to 30mm | ±0.18mm | ±0.20mm |
| Over 30mm to 53mm | ±0.20mm | ±0.25mm |
| Over 53mm to 70mm | ±0.25mm | ±0.30mm |
| Over 70mm to 90mm | ±0.30mm | ±0.35mm |
| Over 90mm to 115mm | ±0.35mm | ±0.44mm |
| Over 115mm to 150mm | ±0.44mm | ±0.55mm |
| Over 150mm to 200mm | ±0.55mm | ±0.70mm |
| Over 200mm to 250mm | ±0.70mm | ±0.80mm |
| Over 250mm to 320mm | ±0.75mm | ±0.90mm |
| Geometric characteristic | Applicable dimension | Tolerance |
|---|---|---|
| Perpendicularity | 0–10mm | 0.2mm |
| Over 10mm | 0.3mm | |
| Symmetry | All | 0.3mm |
| Straightness | Over 0mm to 100mm | 0.2mm |
| Parallelism | Over 100mm to 150mm | 0.3mm |
| Over 150mm | 0.5mm |
Eight model-specific technical drawings are attached for outline, mounting and electrical selection.
