| Part Number: | ULO | - | TB39 | - | 5VHM | / | 7.62 | - | 02 | P | - | 4 | 000A |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Explanation: |
Brand |
Series Code |
Model 5VH - Vertical header without fixing flanges |
Pitch 7.62 - 7.62mm |
Mating Poles 02–12 - Two-digit count from 2 to 12 mating poles; multiple PCB solder tails per pole do not increase this count |
Pole Suffix |
Colour 1 - Grey |
Customer Requirements 000A - Standard suffix shown in the four drawings |
These single-row pluggable PCB headers combine a 7.62mm contact pitch with through-hole solder termination. Choose 5VH for vertical mating or 5RH for right-angle mating. The M versions add end fixing with M3 nuts. Each contact has multiple solder tails; the number of PCB tail rows does not change the pole count.
| Model | Mating orientation | Fixing | Poles | Solder tails per pole |
|---|---|---|---|---|
| TB39-5VH/7.62 | Vertical | Without end fixing | 2–12 | 2 |
| TB39-5VHM/7.62 | M3 nuts | |||
| TB39-5RH/7.62 | Right angle | Without end fixing | ||
| TB39-5RHM/7.62 | M3 nuts | 3 |
The following condition-specific ratings apply to all four models.
| IEC overvoltage category | Pollution degree | Rated current | Rated voltage | Rated impulse voltage |
|---|---|---|---|---|
| III | 3 | 41A | 500V | 6kV |
| 2 | 800V | |||
| II | 1000V |
| UL use group | Rated current | Rated voltage |
|---|---|---|
| B | 41A | 300V |
| C | Not specified | Not specified |
| D | 5A | 600V |
Dielectric withstand voltage is 1.6kV; waveform and test duration are not specified.
| Parameter | Specification |
|---|---|
| Housing | PA66, UL94V-0; both housing components on M versions use PA66 |
| Insulation material group | I |
| Contact | Tin-plated copper |
| M-version fixing nut | Zinc-plated steel, M3 |
| M-version tightening torque | 0.5N·m |
| Protection rating | IP20 |
| Operating temperature | -40°C to +105°C |
| Soldering temperature and time | 260°C for 5 seconds |
| RoHS compliance | Declared |
| Field | Selection |
|---|---|
| Series and model | TB39 with 5VH/7.62, 5VHM/7.62, 5RH/7.62 or 5RHM/7.62 |
| Pole code | 02P–12P |
| Colour code | 1: Grey; 2: Blue; 3: Black; 4: Green; 5: Orange; 6: Red; 7: Transparent; 8: Yellow; 9: White |
| Customer requirement suffix | 000A standard designation |
Select the complete model and pole count before matching a mating connector. Pitch alone does not establish compatibility.
Dimensions are in millimetres. N is the number of mating poles. The plain 5VH drawing depicts a four-pole example; the variable-length relationships are also shown on the corresponding 5RH outline.
| Model | Longitudinal outline | Body dimensions across the end view | Tail projection | Pin width × thickness |
|---|---|---|---|---|
| 5VH and 5RH | 7.62×N+2.60 overall; 7.62×N+2.00 reference upper outline | 29.00×14.25; lower depth 13.50 | 5.00 | 0.80×1.00 |
| 5VHM | 7.62×(N+2) | 29.00×14.25 | ||
| 5RHM | 29.00×14.25; lower depth 13.50 |
| PCB layout parameter | 5VH | 5VHM | 5RH | 5RHM |
|---|---|---|---|---|
| Contact pitch | 7.62 | |||
| First-to-last contact span | 7.62×(N−1) | |||
| PCB hole diameter | 1.60 | |||
| Tail-row arrangement | 2 rows, 7.62 apart | 3 rows; outer span 7.62, intermediate offset 5.08 from the first row | ||
| Nearest row to indicated body edge | 3.40 | 1.83 | ||
| End contact to longitudinal end | 5.11 | 11.43 | 5.11 | 11.43 |
| Fixing centre to end contact | Not applicable | 7.62 | Not applicable | 7.62 |
| Fixing centre to indicated lower body edge | Not applicable | 12.30 | Not applicable | 12.30 |
| Fixing aperture diameter | Not applicable | 2.60 | Not applicable | 2.60 |
Use these tolerances where an individual dimension has no separately stated tolerance.
| Dimension range | Total pitch tolerance | Nominal dimension tolerance |
|---|---|---|
| Over 0mm to 30mm | ±0.18mm | ±0.20mm |
| Over 30mm to 53mm | ±0.20mm | ±0.25mm |
| Over 53mm to 70mm | ±0.25mm | ±0.30mm |
| Over 70mm to 90mm | ±0.30mm | ±0.35mm |
| Over 90mm to 115mm | ±0.35mm | ±0.44mm |
| Over 115mm to 150mm | ±0.44mm | ±0.55mm |
| Over 150mm to 200mm | ±0.55mm | ±0.70mm |
| Over 200mm to 250mm | ±0.70mm | ±0.80mm |
| Over 250mm to 320mm | ±0.75mm | ±0.90mm |
| Geometric characteristic | Applicable dimension | Tolerance |
|---|---|---|
| Perpendicularity | 0–10mm | 0.2mm |
| Over 10mm | 0.3mm | |
| Symmetry | All | 0.3mm |
| Straightness | Over 0mm to 100mm | 0.2mm |
| Parallelism | Over 100mm to 150mm | 0.3mm |
| Over 150mm | 0.5mm |
Four model-specific technical drawings are attached with electrical ratings, ordering fields, outlines and PCB layouts.
