| Part Number: | ULO | - | TB01 | - | 15VM | / | 3.5 | - | 02 | P | - | 4 | 000A |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Explanation: |
Brand |
Series Code TB00 - 2.5mm; 15VC or 15RC |
Model 15VC - Vertical, plain ends; all four listed pitches |
Pitch 2.5 - 2.5mm; TB00 |
Poles 02–24 - Two-digit count from 2 to 24 poles |
Pole Suffix |
Colour 1 - Grey |
Customer Requirements 000A - Standard configuration shown in the scoped header drawings |
The 15 family provides through-hole PCB headers with one straight row of contacts. Choose the exact pitch, pole count, mating direction and end fixing before laying out the board. V versions mate vertically, R versions have right-angle contacts, and L versions provide an inclined mating face. C versions have plain ends, M versions have threaded end inserts, and G versions have locking lugs. The 15RC-LD/3.5 is a separate covered configuration.
All listed models support 2–24 poles. Match the mating connector by contact geometry, keying and model drawing; similar appearance or pitch alone does not establish interchangeability.
| Model | Pitch | Mating direction | End configuration |
|---|---|---|---|
| TB00-15VC/2.5 | 2.5mm | Vertical | Plain |
| TB00-15RC/2.5 | Right-angle | ||
| TB01-15VC/3.5 | 3.5mm | Vertical | |
| TB01-15VM/3.5 | Threaded inserts | ||
| TB01-15VG/3.5 | Locking lugs | ||
| TB01-15RC/3.5 | Right-angle | Plain | |
| TB01-15RM/3.5 | Threaded inserts | ||
| TB01-15RG/3.5 | Locking lugs | ||
| TB01-15RC-LD/3.5 | Individual transparent covers | ||
| TB01-15LC/3.5 | Inclined | Plain | |
| TB01-15LM/3.5 | Threaded inserts | ||
| TB13-15VC/3.81 | 3.81mm | Vertical | Plain |
| TB13-15VM/3.81 | Threaded inserts | ||
| TB13-15VG/3.81 | Locking lugs | ||
| TB13-15RC/3.81 | Right-angle | Plain | |
| TB13-15RM/3.81 | Threaded inserts | ||
| TB13-15LC/3.81 | Inclined | Plain | |
| TB13-15LM/3.81 | Threaded inserts | ||
| TB27-15VC/5.08 | 5.08mm | Vertical | Plain |
| TB27-15VM/5.08 | Threaded inserts | ||
| TB27-15RC/5.08 | Right-angle | Plain | |
| TB27-15RM/5.08 | Threaded inserts |
IEC conditions below are expressed as overvoltage category / pollution degree. Values apply only to the models and conditions in the corresponding row.
| Models | IEC condition | Rated current | Rated voltage | Impulse voltage |
|---|---|---|---|---|
| TB00-15VC/2.5, TB00-15RC/2.5 | II/2 | 5A | 250V | 2.5kV |
| TB01-15VC/3.5, 15VM/3.5, 15VG/3.5, 15RC/3.5, 15RG/3.5 | 7A | |||
| TB01-15RM/3.5 | 10.5A | |||
| TB01-15RC-LD/3.5 | III/3 | 8A | 160V | |
| III/2 | ||||
| II/2 | 250V | |||
| TB01-15LC/3.5, TB01-15LM/3.5 | 12A | |||
| TB13-15VC/3.81, 15VM/3.81, 15VG/3.81, 15RC/3.81, 15RM/3.81 | 7A | |||
| TB13-15LC/3.81, TB13-15LM/3.81 | 12A | |||
| TB27-15VC/5.08, 15VM/5.08, 15RC/5.08, 15RM/5.08 | 7A | 450V | 4kV |
| Models | UL group B | UL group C | UL group D | |||
|---|---|---|---|---|---|---|
| Current | Voltage | Current | Voltage | Current | Voltage | |
| Both TB00 2.5mm models | 4A | 150V | 4A | 150V | 4A | 150V |
| All listed TB01, TB13 and TB27 models | 8A | 300V | Not specified | Not specified | 8A | 300V |
| Property | Specification |
|---|---|
| Termination | Through-hole solder pins; single straight row |
| Pole count | 2–24 |
| Protection level | IP20 |
| Operating temperature | -40°C to +105°C |
| Insulation | PA66, material group I |
| Flammability | UL94V-0 |
| Contact finish | Tin plated |
| Models | Contact material | End insert material |
|---|---|---|
| TB00-15VC/2.5, TB00-15RC/2.5 | Brass | Not applicable |
| TB01-15VC/3.5, TB01-15VG/3.5 | Red copper | |
| TB01-15VM/3.5 | Brass | |
| TB01-15RC/3.5, TB01-15RG/3.5, TB01-15RC-LD/3.5 | Brass | Not applicable |
| TB01-15RM/3.5 | Brass | |
| TB01-15LC/3.5, TB13-15LC/3.81 | Copper alloy | Not applicable |
| TB01-15LM/3.5, TB13-15LM/3.81 | Copper alloy | |
| TB13-15VC/3.81, TB13-15VG/3.81, TB13-15RC/3.81 | Red copper | Not applicable |
| TB13-15VM/3.81, TB13-15RM/3.81 | Brass | |
| TB27-15VC/5.08, TB27-15RC/5.08 | Brass | Not applicable |
| TB27-15VM/5.08, TB27-15RM/5.08 | Brass |
Specify the full model, pitch, pole count and color. N denotes the number of poles in the dimension formulas. The prefix identifies the pitch family: TB00 for 2.5mm, TB01 for 3.5mm, TB13 for 3.81mm and TB27 for 5.08mm. Use only the combinations listed above.
| Code field | Selection |
|---|---|
| Model | 15VC, 15VM, 15VG, 15RC, 15RM, 15RG, 15RC-LD, 15LC or 15LM, as listed for the pitch |
| XXP | Two-digit pole count, 02P–24P |
| Color | 1 grey; 2 blue; 3 black; 4 green; 5 orange; 6 red; 7 transparent; 8 yellow; 9 white |
| Standard suffix | 0A; retain the full model-specific order code |
| Generic screw fields | The shared legend identifies screw head 0 = slot and 1 = cross, and clamping direction 0 = screw down and 1 = screw up; these do not add wire-clamping screws to a PCB header. |
Both 2.5mm models have an overall length of [2.5N+1.9]mm and a contact span of 2.5(N−1)mm. Their body section is 10.1mm × 8.1mm, with a 7.9mm internal section reference, 0.8mm square pins and a 2.2mm end-to-contact reference. The vertical version has a 3.5±0.3mm solder-pin projection and 4.2mm PCB edge reference; the right-angle version has a 3.8±0.3mm projection, 1.2mm PCB edge reference and Ø1.4mm holes. Use the respective drawing for orientation.
| Model | Body length | End-to-first contact | PCB edge-to-row | Section offset |
|---|---|---|---|---|
| TB01-15VC/3.5 | [3.5(N−1)+4.3]mm | 2.15mm | 3mm | 0.30mm |
| TB01-15VM/3.5 | [3.5(N−1)+13.8]mm | 6.9mm | ||
| TB01-15VG/3.5 | [3.5(N−1)+4.3]mm, excluding lugs | 2.15mm | 0.20mm | |
| TB01-15RC/3.5 | [3.5(N−1)+4.3]mm | 8mm | 0.30mm | |
| TB01-15RM/3.5 | [3.5(N−1)+13.8]mm | 6.9mm | 0.20mm | |
| TB01-15RG/3.5 | [3.5(N−1)+4.3]mm, excluding lugs | 2.15mm |
These six models have 0.8mm square pins, Ø1.4mm PCB holes and body section references of 9.2mm and 7mm. The G locking lugs project 1.3mm at each end. The contact span is 3.5(N−1)mm. VC, VM, VG, RC and RM drawings specify 3.5±0.3mm solder-pin projection. RC has an additional 0.45mm detail on its underside view. The RG drawing should be used directly for its pin geometry.
The TB01-15RC-LD/3.5 has separate transparent contact covers. Its 3.5mm pitch, 2–24 poles and electrical ratings are listed above; do not substitute the standard RC mechanical outline for this configuration.
| Model | Body length | PCB edge-to-row | PCB hole diameter | Section offset |
|---|---|---|---|---|
| TB13-15VC/3.81 | [3.81(N−1)+4.6]mm | 3mm | Ø1.2–1.4mm | 0.30mm |
| TB13-15VM/3.81 | [3.81(N−1)+14.16]mm | Ø1.4mm | See drawing | |
| TB13-15VG/3.81 | [3.81(N−1)+4.6]mm, excluding lugs | Ø1.2–1.4mm | 0.20mm | |
| TB13-15RC/3.81 | [3.81(N−1)+4.6]mm | 8mm | ||
| TB13-15RM/3.81 | [3.81(N−1)+14.16]mm | See drawing | 0.21mm |
All five models use 0.8mm square pins and a 3.5±0.3mm solder-pin projection. Body section references are 9.2mm and 7mm, with the model-specific offset shown separately. VC has a 7.30±0.1mm overall section and a [3.81(N−1)±0.5]mm contact-span dimension. VG has a 7.20±0.1mm overall section, 9.20±0.1mm axial reference and 1.3mm locking lugs. VC and VG have 2.3mm end-to-contact references. RM has 4.78mm end blocks, a 5.70mm block-height reference and 4.45mm from the outer contact to the fixing center. RC includes a 4.49mm internal section reference. Follow each figure for the dimension datums.
| Model | Body length | End-to-first pin | Contact span |
|---|---|---|---|
| TB01-15LC/3.5 | [3.5N+0.8]mm | 2.15mm | 3.5(N−1)mm |
| TB01-15LM/3.5 | [3.5N+10.4]mm | 6.95mm | |
| TB13-15LC/3.81 | [3.81N+0.81]mm | 2.31mm | 3.81(N−1)mm |
| TB13-15LM/3.81 | [3.81N+10.39]mm | 7.105mm |
All four inclined versions have a 9.68mm body-depth reference, 0.8mm square pins, a 3.9±0.3mm solder-pin projection, Ø1.4mm PCB holes and a 3.2mm edge-to-row reference. Their mating-face references are 10.4mm and 6.4mm. LM models show 4.4mm from the end fixing center to the nearest contact. The 3.81mm LC side view additionally shows 12mm and 8.44mm sloping dimensions.
| Model | Overall length | PCB edge-to-row | Fixing-center span |
|---|---|---|---|
| TB27-15VC/5.08 | [5.08N]mm | 3mm | Not applicable |
| TB27-15VM/5.08 | [5.08(N−1)+14.68]mm | [5.08(N−1)+8.8]mm | |
| TB27-15RC/5.08 | [5.08N]mm | 1.1mm | Not applicable |
| TB27-15RM/5.08 | [5.08(N−1)+14.68]mm | [5.08(N−1)+8.8]mm |
The four 5.08mm models have a contact span of 5.08(N−1)mm, body section references of 9.2mm and 7mm, a 3.4±0.3mm solder-pin projection, 0.8mm pins and Ø1.4mm PCB holes. VM and RM have a 4.4mm fixing-center-to-contact reference and a 5.85mm end-block reference.
Explicit dimension tolerances take precedence over the general values below. Apply the table to the appropriate dimension range.
| Dimension range | Total pitch tolerance | Nominal dimension tolerance |
|---|---|---|
| Over 0mm to 30mm | ±0.18mm | ±0.20mm |
| Over 30mm to 53mm | ±0.20mm | ±0.25mm |
| Over 53mm to 70mm | ±0.25mm | ±0.30mm |
| Over 70mm to 90mm | ±0.30mm | ±0.35mm |
| Over 90mm to 115mm | ±0.35mm | ±0.44mm |
| Over 115mm to 150mm | ±0.44mm | ±0.55mm |
| Over 150mm to 200mm | ±0.55mm | ±0.70mm |
| Over 200mm to 250mm | ±0.70mm | ±0.80mm |
| Over 250mm to 320mm | ±0.75mm | ±0.90mm |
| Geometric characteristic | Applicable dimension | Tolerance |
|---|---|---|
| Perpendicularity | 0–10mm | 0.2mm |
| Over 10mm | 0.3mm | |
| Symmetry | All | 0.3mm |
| Straightness | Over 0mm to 100mm | 0.2mm |
| Parallelism | Over 100mm to 150mm | 0.3mm |
| Over 150mm | 0.5mm |
