| Part Number: | ULO | - | TB25 | - | 103 | / | 5.0 | - | 02 | P | - | 4 | 000A |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Explanation: |
Manufacturer ULO - ULO Electronics |
Series TB25 - 5.0mm pitch |
Model 103 - Angled wire entry rising clamp terminal block |
Pitch 5.0 - 5.0mm, TB25 only |
Poles 02–24 - 2–24 poles, written with two digits |
Pole Unit P - Poles |
Color 1 - Grey |
Customer Code 000A - Fixed customer requirements code shown in the drawings |
The 103 rising clamp terminal family provides single-row screw connections in two pitches: TB25-103/5.0 at 5.0mm and TB31-103/5.08 at 5.08mm. The angled housing presents the wire openings and screw access above the board. Both models support 2–24 poles; their solder-pin widths and tail tolerances differ.
| Characteristic | TB25-103/5.0 | TB31-103/5.08 |
|---|---|---|
| Pitch | 5.0mm | 5.08mm |
| Poles and rows | 2–24 poles; one row | |
| Connection and mounting | Screw connection with rising clamp; through-hole PCB soldering | |
| Protection level | IP20 | |
| Operating temperature | -40°C to +105°C | |
| Housing | PA66; material group I; UL94V-0 | |
| Conductive contact and solder pin | Tin-plated brass | |
| Clamp block | Nickel-plated brass | |
| Screw | Zinc-plated steel, M2.5 | |
| Material compliance | RoHS compliance declared | |
Both models are rated 24A at 250V under IEC overvoltage category III, pollution degree 2. UL ratings depend on use group.
| Overvoltage category | Pollution degree | Rated voltage | Rated impulse voltage |
|---|---|---|---|
| III | 3 | Not specified | Not specified |
| 2 | 250V | 4kV | |
| II | Not specified | Not specified |
| UL use group | Rated current | Rated voltage |
|---|---|---|
| B | 20A | 300V |
| C | Not specified | Not specified |
| D | 10A | 300V |
| Wiring parameter | Both models |
|---|---|
| UL conductor range | 24–12AWG |
| Solid conductor | 0.2–2.5mm² |
| Flexible conductor | 0.2–2.5mm² |
| Flexible conductor with ferrule | 0.2–2.5mm² |
| Clamping screw | M2.5 |
| Tightening torque | 0.4N·m |
| Wire stripping length | 7mm |
| Separate fixing screw and torque | Not specified |
Certificate file numbers are unspecified. Use the conductor range and ratings for the applicable system.
| Field | Selection or meaning |
|---|---|
| Series and pitch | TB25 with 103/5.0; TB31 with 103/5.08 |
| Pole field | 02P–24P |
| Colour code | 1 grey; 2 blue; 3 black; 4 green; 5 orange; 6 red; 7 transparent; 8 yellow; 9 white |
| General screw-head field | 0 slot; 1 cross |
| General screw-clamping field | 0 screw down; 1 screw up |
| Standard-product suffix | 0A; model drawings show customer suffix 000A after the colour field |
The general legend uses a two-digit 02–99 pole format across the terminal range; the 103 models are specified for 2–24 poles.
N is the number of poles. Dimensions below are in millimetres. Select the matching pitch and solder-tail specification when designing the PCB.
| Dimension | TB25-103/5.0 | TB31-103/5.08 |
|---|---|---|
| Housing length | 5.0 × N | 5.08 × N |
| First-to-last pin span | 5.0 × (N − 1) | 5.08 × (N − 1) |
| Pin pitch | 5.00 | 5.08 |
| End pin to housing end | 2.50 | Not dimensioned |
| Housing height excluding pins | 15.50 | |
| Housing depth | 13.90 | |
| Solder pin section | 0.90 × 0.80 | 1.00 × 0.80 |
| Solder-tail projection | 3.80±0.30 | 3.70±0.15 |
| PCB hole diameter | Ø1.60 | |
| Pin-row distance from indicated front body edge | 7.80 | |
| Pin-row distance from rear body edge | Not dimensioned | 6.10 |
Individual dimension tolerances take precedence over the general values.
| Dimension range | Total pitch tolerance | Nominal dimension tolerance |
|---|---|---|
| Over 0mm to 30mm | ±0.18mm | ±0.20mm |
| Over 30mm to 53mm | ±0.20mm | ±0.25mm |
| Over 53mm to 70mm | ±0.25mm | ±0.30mm |
| Over 70mm to 90mm | ±0.30mm | ±0.35mm |
| Over 90mm to 115mm | ±0.35mm | ±0.44mm |
| Over 115mm to 150mm | ±0.44mm | ±0.55mm |
| Over 150mm to 200mm | ±0.55mm | ±0.70mm |
| Over 200mm to 250mm | ±0.70mm | ±0.80mm |
| Over 250mm to 320mm | ±0.75mm | ±0.90mm |
| Geometric characteristic | Applicable dimension | Tolerance |
|---|---|---|
| Perpendicularity | 0–10mm | 0.2mm |
| Over 10mm | 0.3mm | |
| Symmetry | All | 0.3mm |
| Straightness | Over 0mm to 100mm | 0.2mm |
| Parallelism | Over 100mm to 150mm | 0.3mm |
| Over 150mm | 0.5mm |
